Build: 650X6


It’s been a while since we built a hexacopter. We’ve chosen the Hobbyking 650X6 for it’s affordable price. This will be more for use to lift heavier loads with redundancies.


When folded this hex is 9250mm with 10 inch prop from center motor to opposite center motor.

680mm motor center to motor center and width 340mm when folded.

When opened and ready to fly, it’s 680mm than the named 650mm X6.


Above: No love for the 650X6, not even a box. It comes in plastic bags. You pay for what you get. It’s only USD $29…


One page instruction.


Tubes are 15mm x 15mm

DSC00511 DSC00512

Above: Design of the motor mounts. Cumbersome and hard to install thus we only installed only 2 of them…it lead to bad choices. See flight video at the end.

DSC00513 DSC00514 DSC00515 DSC00516 DSC00517 DSC00519 DSC00521 DSC00522 DSC00523 DSC00524 DSC00525

Motors fitted, Emax 2213 with 10 inch prop. Going to run 4S on this.

DSC00526 DSC00527 DSC00528 DSC00529

Above: Note the mounting of the horizontal bars under the hex for these are about 71mm center to center of hole on the rubber.

DSC00530 DSC00537 DSC00538

Above: Messy cabling, get it flying first. Tidy up later.

DSC00539 DSC00540 DSC00541 DSC00542 DSC00543 DSC00544 DSC00545 DSC00546 DSC00547 DSC00548 DSC00549 DSC00550 DSC00551 DSC00552 DSC00553 DSC00554


– Hobbyking 650X6
– Emax 2213 motors
– Gemfan 10 inch propellers
– 4S 5200mha Multistar
– DJI Naza M V2 with GPS, miniOSD
– Frsky D4R II


Nothing broken but one motor came off during flight. We did hear some wierd sound thus the really low flying and came close to take a look…then flew out and the motor came off. Time to install more of those cumbersome nylon poles.

Building: Immersion RC Xugongs


1 March 2015

This is a compiled article of the Xugong 8, 10 and 10 V2 Pro that’s also posted to Flitetest. We do not hope to post 3 separate article to have visitors having too long articles to go through.

The Xugongs has got to be one of the smallest-when-folded travel quad you can find out there with innovative folding of the arms. It may not be the cheapest to replace during a crash, we know, we crashed shortly after getting the Xugong 10 on the 3rd flight and had to replace the top assembly (USD$32 here). The arms collapse into itself which when folded, is like a tiny 250mm based quad. When unfolded, it takes 10 inch props for the Xugong 10, carries a gimbal and easily carries a 4S 5000 mAh lipo with small modifications.

With the V2, Immersion has made it even better with improvements on the PDB to integrate video camera switching, OSD in a nice red based board (officially these are stated OSD, Camera switch,GoPro Power Supply (5.0 V), GPS Interface, Current/Voltage Sensor, PPM in/out). It’s also a great system if you are already on ImmersionRC system, you’ll be familiar on the setup however, on the other hand, it does locks you to the brand. With ImmersionRC making some leading technologies and constantly improving on it, we think it’s not an issue.

We’ll provide a short introduction to things that’s the same across all Xugongs here before we delve more into each. For even more details, refer to the links of each individual Xugong at the end of this whole article.

The Xugong T Nut System.

It’s quite a good system but with out big fingers, at times, it’s not easy to insert the nut.

The Xugong Foldable Arms

This is one of the best among the many types we have seen and we’ve tried quite a few, from folding backwards to folding inwards. One type we didn’t try is the “umbrella” type where the arms fold down. A famous and popular example are on the DJI S1000/ S900 series of multicopter. We just think it won’t make it small since you’ll have a “bucket” of a quad to deal with, trying to fit that into a bag.

The problem of a heavy butt

This is prevalent immediately after you have assemble any Xugong. The Center of Gravity (CG) is simply off by too much. That said, the Xugong was not designed to hold what we prefer, the 4S 5000 mAh lipo. Even with the 3S 2650 mAh, it’s out of balance. You must fit a gimbal with camera to balance out the quad. To overcome this, we removed the original side covers and replaced them with standoffs from Goodluckbuy. Those standoffs are what’s used in TBS Discovery, just taller.

Rubber Balls

All Xugong uses the rubber balls vibration system totalling 8 each that isolates the whole frame from the motors and propellors. You can get away with slightly balanced propellors and get no vibrations/ jello on your video footage, however, when you do crash, they can be tiny little pesky things to put back.

We fly all the Xugongs with a Turnigy 9XR.


Xugong 8
– Unpack
– Assembly
– Parts List
– Likes
– Dislikes
– Conclude

Xugong 10
– Unpack
– Assembly
– Parts List
– Likes
– Dislikes
– Conclude

Xugong 10 V2 Pro
– Unpack
– Assembly
– Parts List
– Likes
– Dislikes
– Conclude


DSC09023Xugong 8
– Unpack



The Xugong comes in nice boxes and a egg shell type holders for the many items that’s included.

– Assembly

The included instruction is more than enough to put the whole frame together. We drill holes and mounted the Tarot gimbal in front while strapping the 5000 mAh lipo under that allow us to shift it front and back to balance the whole quad. We also use some stand offs to make the center of the quad taller to fit the tarot gimbal motors.

– Parts List


Our Xugong 8 original setup uses:

– Emax 2213
– 20A ESC SimonK from MyRCMart
– DJI Naza M V2, DJI mini OSD
– Frsky D4R-II
– Boscam 200mW Video transmitter
– Tarot T2-D Gimbal
– 4S 5000 mAh Lipo

– Likes

It’s even smaller, the XG8 being our 2nd XG was smaller and it’s great to bring overseas. We brought it to Bintan, crashed it and still had a blast!

Video below – XG8 hand launched.

The Crash

– Dislikes

The back heavy design. Not that we don’t like it, there’s limited option to what kind of lipo you can use to offset and balance the weight of the whole quad. You can’t go too heavy for longer flight time.

– Conclude


A nifty and easy to travel with quad!


DSC08626Xugong 10
– Unpack

DSC08591 DSC08590 DSC08592

Same box, instructions and egg shell box.

– Assembly

It’s straightforward with the instructions provided.

– Parts List


– MyRCMart 2217 800kv motors
– 20A ESC SimonK from MyRCMart
– DJI Naza M V2
– Frsky D8R-XP
– Boscam 400mW Video transmitter

– Likes

It allows us to put on 10 inch props for even longer flight time with the same 4S 5000 mAh lipo.

– Dislikes

Same back heavy design.

– Conclude

We guess, you cannot like the small folding of it while not liking the back heavy design that all XGs have. It’s still a really portable quad.

Xugong 10 V2 Pro

The Xugong 10 V2 Pro (XG10V2) is basically a supercharged Xugong 10. It folds the same but with no more FR4 materials. It’s all carbon fiber now. The real magic is in the newly designed PCB that’s an awesome red! It has a video camera switcher, OSD and PDB built in. If you take into account getting a camera switcher, ImmersionRC’s OSD separately, the price of the Xugong 10 V2 Pro is actually quite an economically priced.
– Unpack

DSC09273 DSC09276 DSC09286
– Assembly

Immersion RC is experimenting as of writing, a Google Docs that’s online and allow for anyone to edit it. It’s call a “live” instructions manual and throughout the month or so that we have that page open, it does have more and more great information. Immersion does moderate it fairly fast so garbage or misleading information gets deleted quickly.

– Parts List

After returning from Bintan island with the Xugong 8, we have learnt our lessons and started trying out Hobbyking’s Multistar wooden propellors that balanced out of the box. They are surely more rigid than those broken ones at the beach on Bintan.

– Emax 2216 810kv motors
– DJI 30A Opto
– DJI Naza M V2
– Frsky D8R-XP
– Boscam 400mW Video transmitter
Multistar 10 inch wooden prop
– Multistar 4S 5200 mAh Lipo 10C constant
– Zippy compact 4S 5000 mAh
– Likes

The Integrated PCB board with built in ezOSD. It’s easily modified to use a mobius or even the SJ4000 that we use. After 2 broken Gopro 3 Black, we’ve not been using any GoPro for a while.

– Dislikes

Same back heavy design.
– Conclude

Great value for money quad with built in ezOSD, camera switcher and PCB.


Links below are permanently links to the individual Xugong build and are updated as we change update, change, crash and replace anything on the Xugongs. There’s also more pictures. Enjoy!

Xugong 8 detailed article
Xugong 10 detailed article
Xugong 10 V2 Pro detailed article
We bought all our Xugongs from ReadymadeRC
Xugong V2 pro product page

Build: ImmersionRC Xugong8


We like the Xugong 10 so much, we bought the 8 shortly after and it’s as awesome. Waiting for the Xugong Pro v2 to launch and making one more purchase. The Xugong seem is all we need to pack, go and fly. It’s small and the Xugong8 is even more impressive.


Purchased the “crash kit” and extra rubber balls and the red ones that’s suppose to be harder.DSC08998

Same eggshell type tray in the box.DSC08999 DSC09000 DSC09001 DSC09002

ESC power cables shorten.DSC09003 DSC09004

Size compared as seen on our Instagram account previously.DSC09005 DSC09006  DSC09008

Going with a DJI Naza M Lite v2 first, would like to have the Naza M V2 from the Aliencopter soon after we tear that down.DSC09009 DSC09011 DSC09012 DSC09013 DSC09014 DSC09015  DSC09017

Compared folded…DSC09019

…and ready to fly  DSC09021

Gotta change that blue GPS folding mount to a red one!DSC09022

We really like the size but the space within the Xugong8 is like the Xugong10, it’s oddly hard to balance the whole quad. We always like the Naza to sit right in the center with proper Center of Gravity (CG) with front and back balanced. To achieve that, the lipo has to be mounted below the whole quad meaning the Xugong has to be modded to be taller. We hope to keep it at this size.

First Flight

We’ll be able to move the electronics like the LED module, PMU and Frsky D4R II receiver into the current lipo compartment too if we move the lipo to the bottom.

You can add a gimbal to the front to add weight to it and try to balance it. We flew it with Emax 2213 935kv motors, 8 inch propellers, a gopro3 black in the underwater housing and it lasted about 10.5 mins on a Turnigy 3S 20-30C 2650mah lipo.

Conclude, you can’t find a better travel quad as of Jan 2015. The arms folding mechanism is simply well thought through and is genius! It unpacks, unfold the arms in seconds and ready to fly. No screws and nuts to fiddle with or to tighten before you can fly like the Aliencopter 430mm we have! It makes it a pain when we tried flying the Aliencopter at St John’s Island/ Kusu Island we simply stop disassembling it and hung it outside the bag. It’s sure to raise questions and unwanted attention at certain areas to fly.

The 8 inch version of the Xugong is really small for it’s class, when folded (and we’ve looked at what is available and tried just about all of them backwards folding, fold inwards etc etc) and we see ourselves travelling with it overseas even.


Our Xugong 10 build
Xugong Pro V2 build
Discussion –
We bought at –